Hi Gurus,
We have a SAP Netweaver PI 7.11 Dual-Stack System that currently has only PAS (CI) instance. We would like to perform split of ASCS (ABAP Central Service Instance) from PAS (CI). We believe this is done via SWPM sapinst. Can you advise on the steps to consider in performing the split and procedures?
I would appreciate your help and assistance on this. Thanks.
Best regards,
Philip
Hello Experts,
This could happen on any type of system I suspect, but it is on my Solution Manager (7.01 on Eh1). I downloaded a support stack (27)and was checking the components requirements. I use the Directory box in SPAM, and I go into New Support Packages. I highlight the support package for ST 400 then click on the Queue button. It comes back with this message: OCS package SAPKITL437 does not match the current software component vector.
I click continue and the requirements window comes up. It shows that I have currently loaded the wrong BI_Content. It says: Non-permitted release of add-on BI_CONT installed. The release information is BI_CONT,706.
If I go back to the main window to look at the current package level, I see that BI_CONT component release (loaded) is 704 - sp 8.
I must have gotten very creative when loading that back in 2008. MOPZ was used, but it was before the support stack restrictions were in place on my system.
I can't get around this issue, because even trying to load the Basis support package I get this message.
If anyone has had the problem and knows what to do I would appreciate some help. Notes searching has not found anything. So far my Customer message has not been helpfull, but it is not SAP support .
Pat
Friends,
We're using SUM1.0SP13 patch4 in order to do a PI upgrade from 7.11(sp13) Kernel 721_EXT_REL v331 to 7.40(sp11) Kernel 7.42 v212
Oracle 11g
AIX 6.1 64-bit
I took my time to read the SUM GUIDE and these notes:
SUM note 2039311
Oracle note 2039312
AIX note 1780629
NW note 1751237
And as a result of reading all the notes/SUMguide I applied many notes / changed PRIOR to starting SUM.
Once I started SUM, I reached extraction phase and am STUCK on this error:
In case you can't read the attached PIC, I am in phase PREP_INIT/SETSYNC_PREP_STARTED and I am getting an error saying Last error code set: No synchronization mechanism available
I have tried re-running the phase, but no luck, same error. The logs don't really say much:
CURRENTPHASE PREP_INIT/SETSYNC_PREP_STARTED
...started at 20150806114645
# Setting syncpoint PREPARE=STARTED
..finished at 20150806114645 with status ABORTED.
# Error message set: 'No synchronization mechanism available'
...begin dialog at 20150806114658
I cannot find any notes/threads or searches that address this issue.
I'll open a message if I must, but I'd rather submit here first to see if anyone has an idea!
Thanks
NICK
Currently we have a ERP landscape consist of DEV/QAS/PRD and there's another ERP system separately copied in the past for reference purpose.
Days ago, we required to create a new transport request in the reference system and copy it to a current developement system. Hence, I manually access the file system and copied relevant datafile and cofile of the transport request. However, when I add this TR into the current development system, I realized that the same no. of request w/ different objects and description was already created and released. For that reason, even if I added the new transport request in DEV in STMS, the system still recognize it as the one which is released previously.
Is there any ways that I can do to avoid such problem?
Hi experts.
We are in a project to upgrade our PI from 7.02 SP16 to 7.5 SP02, Oracle 12, Linux RedHat 6.3, and in the execution step show us this error:
Last error code set: RFC error system SID nr 11 function 'SUBST_HANDLE_UVERS' failed with code 3 key
DBSQL_NO_MORE_CONNECTION: No resources available for further secondary database connections.
Have you ever seen this error before?
We didn't find SAP Notes to help us.
If experts could help with this trouble,
Thanks
Marcos
Dear experts,
I'm trying to set up SUM parameters for my system but there is a step I can't pass through.
When SUM asks me about central instance profiles I input files like this:
However in this case I have strange messages: Please enter a valid path
I have no idea how to deal with this issue:
1) Filenames are absoultely correct and they exist in sid/sys/profiles directory
2) I don't have a start profile as I don't need it
Is there any way to debug this problem? Can it be related somehow yo security srttings of the server?
Thanks!
hi,
I am on iSeries (AS400) and upgrading NW 7.4 (ABAP only) SPS9 to SPS14.
SUM is SP16(PL2)
I had to exit the SUM browser at end of day(with SUM process still running)
and i had daily backup running which prevented a directory being read,
which caused the SUM process to be error-ed out. Now the backup has
completed and all the directories are accessible. When i try to get
into
SUM browser it logs me in with sidadm without any issues, but the
screen
say
The tool is not running
When i click next, it says error occurred
Error Details :
Status Code : 503
Status text : Service Unavailable
Detailed Message : Message from service : SAPup process exited with
status -1 ,| Check the browser console for more information.
Any idea on how to fix this issue?
SAPHOSTAGENT is on the latest version
I have restarted saphostagent, also tried to register SUM to hostagent
again. Killed SUMSTART job PGM-SAPup-real from the OS level. None of
these steps helped.
Output of the failed tool:
Output of failed tool
execution:EXEC> Starting subprocess with PID 59023 at 20160316143013
ENV: DIR_LIBRARY=/sapmnt/DBW/exe/uc/as400_pase_64 ENV:
ILE_PATH=/sapmnt/DBW/exe/uc/as400_pase_64:/usr/bin:. ENV:
LIBPATH=/sapmnt/DBW/exe/uc/as400_pase_64 ENV:
PASE_LIBPATH=/sapmnt/DBW/exe/uc/as400_pase_64 ENV:
PASE_LOCPATH=/usr/lib/nls/loc ENV:
PASE_PATH=/sapmnt/DBW/exe/uc/as400_pase_64:/QOpenSys/usr/bin:/usr/ccs/bin:/QOpenSys/usr/bin/X11:/usr/sbin:/usr/bin:.
ENV: PASE_STDIO_ISATTY=N ENV: PASE_THREAD_ATTACH=Y ENV:
PASE_TZ=<MST>7<MDT>,M3.2.0,M11.1.0 ENV: PASE_USRGRP_LIMITED=
ENV:
PATH=/sapmnt/DBW/exe/uc/as400_pase_64:/QOpenSys/usr/bin:/usr/ccs/bin:/QOpenSys/usr/bin/X11:/usr/sbin:/usr/bin:.
ENV: SAPSYSTEMNAME=DBW ENV: dbms_type=db4 ENV: dbs_db4_rdbname=SAPDATA
PWD: /SAPDATA/usr/sap/DBW/SUM/abap EXECUTING
/SAPDATA/usr/sap/DBW/SUM/abap/bin/SAPup rootdir=/usr/sap/DBW/SUM/abap
guiconnect=127.0.0.1:54821 Assertion failed: CurrentModuleDef != NULL, file
SAPupmodule.c, line 186 *** FATAL: Got signal 'SIGABRT' (6)! Please contact the
SAP support! *** FATAL: SAPup got signal in phase '', stack trace written to
dev_SAPup.
SAPupConsole.log:03/16/2016 at 00:53:05- this is last error
Converting 3 entries from 'CHECKS.LOG'
>> Current module status: continue with phase PREP_GENCHECKS/CONFCHK
Converting 3 entries from 'CHECKS.LOG'
>> Waiting for request handler...
*** FATAL ERROR: Cannot open '/usr/sap/DBW/SUM/abap/tmp/SAPupDialog.txt': Device busy
Error processing dialog 'DeleteFileFailed'
Note- the above issue is what caused the initial error in SUM due the iSeries backup. This directory is accessible now after backup is completed.
Hello,
I'm importing several Support Packages to update my Solution Manager 7.1 System up to Solution Tools ST SP14 (SAPKITL714). I used the SPAM Queue Calculator to add all the required Support Packages and extra Components.
Unfortunatelly the process stopped in the IMPORT_PROPER phase due to missing Tables.
- Error in phase: IMPORT_PROPER
- Reason for error: TP_STEP_FAILURE
- Return code: 0008
- Error message: OCS Package SAPKITL714, tp step "I", return code 0008
Checking the Log FileSAPIITL714.<SID> located in /usr/sap/trans/log :
Details of the Log (too long to attach it):
…
3 ETW674Xstart import of "R3TRTABU/UI5/TREP_FILES" ...
3WETW109 table "/UI5/TREP_FILES" does not exist in nametab.
4 ETW000 no entries for /UI5/TREP_FILES will be imported in this step.
2EETW109 table "/UI5/TREP_FILES" does not exist in nametab.
3 ETW676 end import of "R3TRTABU/UI5/TREP_FILES" (warnings).
…
…
3 ETW674Xstart import of "R3TRTABU/UI5/TREP_TEXT" ...
3WETW109 table "/UI5/TREP_TEXT" does not exist in nametab.
4 ETW000 no entries for /UI5/TREP_TEXT will be imported in this step.
2EETW109 table "/UI5/TREP_TEXT" does not exist in nametab.
2EETW109 table "/UI5/TREP_TEXT" does not exist in nametab.
…
…
3 ETW674Xstart import of "R3TRTABU/UI5/TREP_TEXT_T" ...
3WETW109 table "/UI5/TREP_TEXT_T" does not exist in nametab.
4 ETW000 no entries for /UI5/TREP_TEXT_T will be imported in this step.
2EETW109 table "/UI5/TREP_TEXT_T" does not exist in nametab.
2EETW109 table "/UI5/TREP_TEXT_T" does not exist in nametab.
…
I've found out that SAP Note 2223723 states that the SPAM Check Component Software have an error for the
Component UISAPUI5 (It should be >= SP12 for SolMan 7.1 ST SP14). The missing tables seems to belong to the UISAPUI5 component.
The solution in this SAP Note is to modify the Check Component Software to force to check the UISAPUI5 Component to be greather than SP 12 BEFORE applying the Support Package 7.1 SP14, but this is too late because we already have the problem in the Import_Proper phase.
What can we do to fix the error?
Should we apply SAP Note 1022755 to force the Import phase to skip the Check up for these Tables during the IMPORT_PROPER phase? Won't this be a problem later for the UISAPUI5 Component and Tables that weren't updated by this Support Package?
Should we do a system recover and start over the process?
Thanks a lot for your help!
Miguel Vizcaino
Error-Message from SUM-Tool:
The executable R3trans in /usr/sap/EXE/SUM/abap/exe is too old.
It needs a release date of 19.03.13 or later.
what is this -
the download of the SUM is just new (from June 2013) ?
Hi everyone,
I'm trying to run the SUM 1.0 SP16 but I'm getting an error when I go to the GUI environment.
If I try to run the STARTUP confighostagent line I get the following message.
E:\usr\sap\ECC\SUM>STARTUP confighostagent eccadm
**** The SID: ECC is detected from <SID>ADM user. ****
**** Configuring SUM Abap ... ****
E:\usr\sap\ECC\SUM\startup.js(138, 2) WshShell.RegRead: Invalid root in registry key "HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\SAP HostAgent\InstallLocation".
Actually I've checked that register but it does not exist.
What values should this register have? and Is it the cause of the first error described?
Thank you all for your help.
Hello,
I'm importing several Support Packages to update my Solution Manager 7.1 System up to Solution Tools ST SP14 (SAPKITL714). I used the SPAM Queue Calculator to add all the required Support Packages and extra Components.
Unfortunatelly the process stopped in the IMPORT_PROPER phase due to missing Tables.
- Error in phase: IMPORT_PROPER
- Reason for error: TP_STEP_FAILURE
- Return code: 0008
- Error message: OCS Package SAPKITL714, tp step "I", return code 0008
Checking the Log FileSAPIITL714.<SID> located in /usr/sap/trans/log :
Details of the Log (too long to attach it):
…
3 ETW674Xstart import of "R3TRTABU/UI5/TREP_FILES" ...
3WETW109 table "/UI5/TREP_FILES" does not exist in nametab.
4 ETW000 no entries for /UI5/TREP_FILES will be imported in this step.
2EETW109 table "/UI5/TREP_FILES" does not exist in nametab.
3 ETW676 end import of "R3TRTABU/UI5/TREP_FILES" (warnings).
…
…
3 ETW674Xstart import of "R3TRTABU/UI5/TREP_TEXT" ...
3WETW109 table "/UI5/TREP_TEXT" does not exist in nametab.
4 ETW000 no entries for /UI5/TREP_TEXT will be imported in this step.
2EETW109 table "/UI5/TREP_TEXT" does not exist in nametab.
2EETW109 table "/UI5/TREP_TEXT" does not exist in nametab.
…
…
3 ETW674Xstart import of "R3TRTABU/UI5/TREP_TEXT_T" ...
3WETW109 table "/UI5/TREP_TEXT_T" does not exist in nametab.
4 ETW000 no entries for /UI5/TREP_TEXT_T will be imported in this step.
2EETW109 table "/UI5/TREP_TEXT_T" does not exist in nametab.
2EETW109 table "/UI5/TREP_TEXT_T" does not exist in nametab.
…
I've found out that SAP Note 2223723 states that the SPAM Check Component Software have an error for the
Component UISAPUI5 (It should be >= SP12 for SolMan 7.1 ST SP14). The missing tables seems to belong to the UISAPUI5 component.
The solution in this SAP Note is to modify the Check Component Software to force to check the UISAPUI5 Component to be greather than SP 12 BEFORE applying the Support Package 7.1 SP14, but this is too late because we already have the problem in the Import_Proper phase.
What can we do to fix the error?
Should we apply SAP Note 1022755 to force the Import phase to skip the Check up for these Tables during the IMPORT_PROPER phase? Won't this be a problem later for the UISAPUI5 Component and Tables that weren't updated by this Support Package?
Should we do a system recover and start over the process?
Thanks a lot for your help!
Miguel Vizcaino
Dear experts,
I'm trying to set up SUM parameters for my system but there is a step I can't pass through.
When SUM asks me about central instance profiles I input files like this:
However in this case I have strange messages: Please enter a valid path
I have no idea how to deal with this issue:
1) Filenames are absoultely correct and they exist in sid/sys/profiles directory
2) I don't have a start profile as I don't need it
Is there any way to debug this problem? Can it be related somehow yo security srttings of the server?
Thanks!
There are or were several 3rd party transport management software solutions on the market at one time. Most of them offered a capability to automatically backout changes (by request ID). does anyone know how this would be possible? I would imagine the software would record the version of each object prior to the change in the target system and then if a rollback is requested it would retrieve that version and substitute it for latest version.
I'm just curious if anyone has had any experience with these tools or replicating similar functionality. I believe TRANSPORT EXPRESS & REALTECH's TransportManager are some of the remaining software solutions still on the market, the other was bought by Oracle.
Hi All,
While using the DMO(database migration option) feature in SUM SP9, UI frequently displays the message "Tool start required" and "The tool is not running".
In one of the DMO documents found that restarting the SAP hostagent should help, i have restarted the hostagent and then logged in, same message. Please suggest.
Regards,
Ravi A
Hello,
I'm importing several Support Packages to update my Solution Manager 7.1 System up to Solution Tools ST SP14 (SAPKITL714). I used the SPAM Queue Calculator to add all the required Support Packages and extra Components.
Unfortunatelly the process stopped in the IMPORT_PROPER phase due to missing Tables.
- Error in phase: IMPORT_PROPER
- Reason for error: TP_STEP_FAILURE
- Return code: 0008
- Error message: OCS Package SAPKITL714, tp step "I", return code 0008
Checking the Log FileSAPIITL714.<SID> located in /usr/sap/trans/log :
Details of the Log (too long to attach it):
…
3 ETW674Xstart import of "R3TRTABU/UI5/TREP_FILES" ...
3WETW109 table "/UI5/TREP_FILES" does not exist in nametab.
4 ETW000 no entries for /UI5/TREP_FILES will be imported in this step.
2EETW109 table "/UI5/TREP_FILES" does not exist in nametab.
3 ETW676 end import of "R3TRTABU/UI5/TREP_FILES" (warnings).
…
…
3 ETW674Xstart import of "R3TRTABU/UI5/TREP_TEXT" ...
3WETW109 table "/UI5/TREP_TEXT" does not exist in nametab.
4 ETW000 no entries for /UI5/TREP_TEXT will be imported in this step.
2EETW109 table "/UI5/TREP_TEXT" does not exist in nametab.
2EETW109 table "/UI5/TREP_TEXT" does not exist in nametab.
…
…
3 ETW674Xstart import of "R3TRTABU/UI5/TREP_TEXT_T" ...
3WETW109 table "/UI5/TREP_TEXT_T" does not exist in nametab.
4 ETW000 no entries for /UI5/TREP_TEXT_T will be imported in this step.
2EETW109 table "/UI5/TREP_TEXT_T" does not exist in nametab.
2EETW109 table "/UI5/TREP_TEXT_T" does not exist in nametab.
…
I've found out that SAP Note 2223723 states that the SPAM Check Component Software have an error for the
Component UISAPUI5 (It should be >= SP12 for SolMan 7.1 ST SP14). The missing tables seems to belong to the UISAPUI5 component.
The solution in this SAP Note is to modify the Check Component Software to force to check the UISAPUI5 Component to be greather than SP 12 BEFORE applying the Support Package 7.1 SP14, but this is too late because we already have the problem in the Import_Proper phase.
What can we do to fix the error?
Should we apply SAP Note 1022755 to force the Import phase to skip the Check up for these Tables during the IMPORT_PROPER phase? Won't this be a problem later for the UISAPUI5 Component and Tables that weren't updated by this Support Package?
Should we do a system recover and start over the process?
Thanks a lot for your help!
Miguel Vizcaino
Hi Experts,
we are performing a upgrade from 7.3 to 7.4. Generated the stack file containing all latest patches from marketplace.
During the configuration phase, we get the validation queue as OK, but there is a warning message stating
"Verification of Signed components finished with status warning "
Check verify-signed-content.log
When checking the VERIFY-SIGNED-CONTENT.LOG file, there are around 5 patches of components with warning messages as below
PM [Warning]: Cannot verify archive /saptest/ABC/VCKITBI06P_1-20010062.SCA : Cannot perform verification, because archive /saptest/ABC/VCKITBI06P_1-20010062.SCA does not contain a META-INF/SAP_DIGSIG_MANIFEST.MF file.
We opened the SCA file and indeed the META-INF/SAP_DIGSIG_MANIFEST.MF file is missing.
All other components have this manifest file and have been successfully verified except for this 5 patches.
My query is how do we sort this out. Tried downloading the SCA files many times, still the same issue.
Is there any issue if I continue the step ignoring this warning?
Has anyone faced similar issues. Pls Suggest
regards,
Sree
Hello,
i have an Issue in running SUM. At Step "MAIN_SHDIMP/SUBMOD_SHD2_RUN/RUN_RSDROPCDSBAS" the Batchjob RSDROPCDSBAS is aborted with the Error "DBSQL_STMNT_TOO_LARGE".
I have read that this Error occurs when the Report tries to select wirh a huge WHERE Condition. But in the Debugging mode we can see that the select table for where condition has only 3672 entrys. Is there any ProfileParameter to fix this issue?
Application Server: 742
OS: Windows x64 / 8Gb RAM / 2 CPUs
Database Server: MaxDB 7.9
OS: Windows x64 / 8 GB RAM / 2 CPUs
Hi guys
While running an ERP EHP7 Upgrade, in phase RUN_CRR_LAST Phase im unable to proceed.
First this phase failed since PXA was too small, so many tables cancelled, therefore I fixed this issue by increasing abap buffersize parameter and no more dumps were found
So, when I try to restart the SUM Process Im stuck in this phase
In the logs its states
1 ETQ359 RFC Login to: System="TEX", AsHost="ARBUE-V-SA03D" Nr="02", GwHost="ARBUE-V-SA03D", GwService="sapgw02"
2 ETQ232 RFC Login succeeded
4 ETQ010 Date & Time: 20150417150518
1 ETQ233 Calling function module "SUBST_CHECK_BATCHJOB" by RFC
2 ETQ373 parameter "JOBNAME" = "RSUPG_ISU_CRR"
2 ETQ373 parameter "JOBCOUNT" = "15051800"
2 ETQ373 parameter "IV_VERIFY" = " "
1 ETQ234 Call of function module "SUBST_CHECK_BATCHJOB" by RFC succeeded
4 ETQ010 Date & Time: 20150417150518
2 ETQ373 parameter "JOBSTATUS" = "F"
2 ETQ374 parameter "RC_CHECK" = "0"
2 ETQ373 parameter "JOBENDDATE" = "20150417"
2 ETQ373 parameter "JOBENDTIME" = "150518"
4 ETQ263 Batchjob "RSUPG_ISU_CRR" finished successfully
1 ETQ124 Scanned file 'log\RSCRRLST.TEX' from offset 17273 to 18454 for errors.
4 ETQ010 Date & Time: 20150417150519
1EETQ399 Last error code set is: Single errors (code <= 8) found in logfile 'RSCRRLST.ELG'
1EETQ203 Upgrade phase "RUN_CRR_LAST" aborted with errors ("20150417150519")
Batchjob "RSUPG_ISU_CRR" finishes successfully, but some how it says it found an error in log RSCRRLST.ELG
RSCRRLST.ELG
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Final data transfer of change recording framework ERRORS and RETURN CODE in RSCRRLST.TEX
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
A4 ESUPG 002 " "
A4 ESUPG 001 -------------------------------------------------------------------------
A4 ESCRR_ISU 005 Action "LAST" started at "15:05:18"("17.04.2015")
A4 ESCRR_ISU 010 Number of used dialog processes set to "6"
A4 ESCRR_ISU 010 Number of used dialog processes set to "10"
A2EESCRR 097 Transition "LAST_TRANSFER" can not be started because transition "START_TRANSFER" failed
A2EESCRR 097 Transition "LAST_TRANSFER" can not be started because transition "START_TRANSFER" failed
And that log only says
Transition "LAST_TRANSFER" can not be started because transition "START_TRANSFER" failed
Im able to login to shadow instannce - Transaction CRR_CONTROL and its in yellow state, ready to be started.
If I started in manually, the upgrade says there is another so It has to be stopped. Then i restart the SUM process and it fails again
RSCRRLST.ELG
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Final data transfer of change recording framework ERRORS and RETURN CODE in RSCRRLST.TEX
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
A4 ESUPG 002 " "
A4 ESUPG 001 -------------------------------------------------------------------------
A4 ESCRR_ISU 005 Action "LAST" started at "15:05:18"("17.04.2015")
A4 ESCRR_ISU 010 Number of used dialog processes set to "6"
A4 ESCRR_ISU 010 Number of used dialog processes set to "10"
A2EESCRR 097 Transition "LAST_TRANSFER" can not be started because transition "START_TRANSFER" failed
A2EESCRR 097 Transition "LAST_TRANSFER" can not be started because transition "START_TRANSFER" failed
RSCRRLST.TEX
A4 ESUPG 002 " "
A4 ESUPG 301 Report name ...: "CL_CRR_BASE_SCENARIO -> CONSTRUCTOR"
A4 ESUPG 302 Log name .: "E:\SUM\abap\tmp\RSCRRLST.TEX"
A4 ESUPG 304 Start time.....: "17.04.2015" "15:05:18"
A4 ESUPG 002 " "
A4 ESUPG 001 -------------------------------------------------------------------------
A4 ESCRR_ISU 005 Action "LAST" started at "15:05:18"("17.04.2015")
A4 ESCRR_ISU 010 Number of used dialog processes set to "6"
A4 ESCRR_ISU 010 Number of used dialog processes set to "10"
A2EESCRR 097 Transition "LAST_TRANSFER" can not be started because transition "START_TRANSFER" failed
A2EESCRR 097 Transition "LAST_TRANSFER" can not be started because transition "START_TRANSFER" failed
A4 ESUPG 001 -------------------------------------------------------------------------
A4 ESUPG 002 " "
A4 ESUPG 301 Report name ...: "CL_CRR_BASE_SCENARIO -> CONSTRUCTOR"
A4 ESUPG 304 Start time.....: "17.04.2015" "15:05:18"
A4 ESUPG 305 End time ......: "17.04.2015" "15:05:18"
A4 ESUPG 002 " "
A4 ESUPG 001 -------------------------------------------------------------------------
4 EPU202XEND OF SECTION BEING ANALYZED END OF RUN_CRR_LAST =================================================
Any idea how to fix this?
Best
Martin
Hi Experts,
I am having problem while importing transport request in production client.
Error message is " Transport control program tp ended with error code 0200".
TRACE file content is as below. Can you please help me on this.
INFO: 20: [ dev trc,00000] 
OCIEnvCreate(mode=16384=OCI_UTF16) returned 0 (for default NLS handle) 29760 0.064853 RACE-INFO: 21: [ dev trc,00000] OCIHandleAlloc(OCI_HTYPE_ERROR, con=0, ErrHp=0BA48F68) 58 0.064911 RACE-INFO: 22: [ dev trc,00000] OCIHandleAlloc(OCI_HTYPE_ERROR, con=0, ErrBt=0BA4A268) 28 0.064939 RACE-INFO: 23: [ dev trc,00000] NLS env. settings: lang=41004D00450052004900430041004E00 64 0.065003 RACE-INFO: 24: [ dev trc,00000] terr=41004D0045005200490043004100 29 0.065032 RACE-INFO: 25: [ dev trc,00000] char=55005400460031003600 12 0.065044 RACE-INFO: 26: [ dev trc,00000] Client NLS setting (by OCINlsGetInfo(con=0)): 'AMERICAN_AMERICA.UTF16' 11 0.065055 RACE-INFO: 27: [ dev trc,00000] charset='UTF16', ncharset='AL16UTF16', UNI_ASC=FALSE 12 0.065067 RACE-INFO: 28: [ dev trc,00000] Connecting as SAPSR3/@ECP on connection 0 (nls 0) ... (dbsl 740 300913, UNICODE[2]) RACE-INFO: 29: 24 0.065091 RACE-INFO: 30: [ dev trc,00000] OCIHandleAlloc(OCI_HTYPE_SVCCTX, con=0, svchp=0BA4C300) 18 0.065109 RACE-INFO: 31: [ dev trc,00000] Allocating server context handle 12 0.065121 RACE-INFO: 32: [ dev trc,00000] Attaching to database server ECP (con=0, svchp=0BA4C300, srvhp=0BA50B20) 38 0.065159 RACE-INFO: 33: [ dev trc,00000] Wed Apr 13 22:02:27 2016 1057356 1.122515 RACE-INFO: 34: [ dev trc,00000] OCIServerAttach(OCI_DEFAULT) failed with -1=OCI_ERROR 10 1.122525 RACE-INFO: 35: [ dev trc,00000] OCIServerAttach(OCI_DEFAULT) failed with SQL error 12638: 120 1.122645 RACE-INFO: 36: [ dev trc,00000] ORA-12638: Credential retrieval failed RACE-INFO: 37: 14 1.122659 TRACE-INFO: 38: [dbsloci.c ,00000] *** ERROR => CONNECT failed with SQL error '12638' 18 1.122677 TRACE-INFO: 39: [ dev trc,00000] >oci_get_errmsg (con=0, rc=12638) 16 1.122693 TRACE-INFO: 40: [ dev trc,00000] OCIErrorGet() -> SQL error code: 12638 59 1.122752 TRACE-INFO: 41: [ dev trc,00000] ORA-12638: Credential retrieval failed TRACE-INFO: 42: 13 1.122765 TRACE-INFO: 43: [ dev trc,00000] ocica() -> SQL error code 12638,12638 11 1.122776 TRACE-INFO: 44: [ dev trc,00000] DbSlConnect(con=0) -> orc=12638, 99=DBSL_ERR_DB 11 1.122787 TRACE-INFO: 45: [ dblink ,00000] ***LOG BY2=>sql error 12638 performing CON 34 1.122821 TRACE-INFO: 46: [ dblink ,00000] ***LOG BY0=>ORA-12638: Credential retrieval failed 11 1.122832 tp returncode summary: TOOLS: Highest return code of single steps was: 0 ERRORS: Highest tp internal error was: 0232 tp finished with return code: 232 meaning: connect failed
Hello, I am updating a SAP System (SAP EWM 9.2 - NW 7.40) with SUM SP16 - PL6. HDB Rev. 112.
In the Phase "PREP_INSTALL/DBCONNCHK_SHD" take this ERROR:
"
4 ETW000 R3trans version 6.25 (release 745 - 27.11.15 - 20:15:12).
4 ETW000 unicode enabled version
4 ETW000 ===============================================
4 ETW000
4 ETW000 date&time : 27.03.2016 - 13:30:22
4 ETW000 control file: <no ctrlfile>
4 ETW000 R3trans was called as follows: R3trans -x -w /SAPINST/fmv/ewx/SUM/abap/log/DBCONNCHKSHD.LOG
4 ETW000 trace at level 1 opened for a given file pointer
4 ETW000 [ dev trc,00000] Sun Mar 27 13:30:22 2016
4 ETW000 [ dev trc,00000] Loading DB library '/SAPINST/fmv/ewx/SUM/abap/exe/dbhdbslib.so' ...
4 ETW000 [ dev trc,00000] Library '/SAPINST/fmv/ewx/SUM/abap/exe/dbhdbslib.so' loaded
4 ETW000 [ dev trc,00000] Version of '/SAPINST/fmv/ewx/SUM/abap/exe/dbhdbslib.so' is "745.04", patchlevel (0.100)
4 ETW000 [ dev trc,00000] switch DBSL TRACE LEVEL from 3 to 1
4 ETW000 [ dev trc,00000] DBHDBSLIB : version 745.04, patch 0.100 (Make PL 0.100)
4 ETW000 [ dev trc,00000] HDB shared library (dbhdbslib) patchlevels (last 10)
4 ETW000 [ dev trc,00000] (0.100) SAP Support Package Stack Kernel 7.45 Patch Level 100 (note 2276394)
4 ETW000 [ dev trc,00000] (0.018) Describe on a decimal datatype with a large scale value (note 2220646)
4 ETW000 [ dev trc,00000] (0.013) Use connection variables instead of table M_CONNECTIONS (note 2207349)
4 ETW000 [ dev trc,00000] (0.008) Session variables processing via dbsl (note 2182777)
4 ETW000 [ dev trc,00000] (0.005) Substitute literals in select list (note 2182777)
4 ETW000 [ dev trc,00000] (0.004) Cancel FDA SQL statement (note 2177669)
4 ETW000 [ dev trc,00000]
4 ETW000 [ dev trc,00000] Loading SQLDBC client runtime ...
4 ETW000 [ dev trc,00000] SQLDBC Module : /usr/sap/EW1/hdbclient/libSQLDBCHDB.so
4 ETW000 [ dev trc,00000] SQLDBC Runtime : libSQLDBCHDB 1.00.112.00 Build 1457615240-1530
4 ETW000 [ dev trc,00000] SQLDBC client runtime is 1.00.112.00.1457615240
4 ETW000 [ dev trc,00000] Try to connect via secure store (UPGSHDKEY) on connection 0 ...
4 ETW000 [ dev trc,00000] no connection data found for key (UPGSHDKEY) in HANA secure store
4 ETW000 [ dev trc,00000] Try to connect via environment (localhost:7878) on connection 0 ...
4 ETW000 [dbhdbsql.cpp,00000] *** ERROR => Connect to database failed, rc=1, rcSQL=-10709
4 ETW000 [ dev trc,00000] SQLCODE : -10709
4 ETW000 [ dev trc,00000] SQLERRTEXT : Connection failed (RTE:[89006] System call 'connect' failed, rc=111:Connection refused (localhost:78\
4 ETW000 [ dev trc,00000] 78))
4 ETW000 [ dblink ,00000] ***LOG BY2=>sql error -10709 performing CON
4 ETW000 [ dblink ,00000] ***LOG BY0=>Connection failed (RTE:[89006] System call 'connect' failed, rc=111:Connection refused (localhost:7878))
2EETW169 no connect possible: "DBMS = HDB --- SERVER = '' PORT = ''"
"
This is the output of "hdbuserstore LIST"
"
DATA FILE : /home/ew1adm/.hdb/?????/SSFS_HDB.DAT
KEY FILE : /home/ew1adm/.hdb/?????/SSFS_HDB.KEY
KEY DEFAULT
ENV : ?????:34615
USER: SAPFRA
KEY UPGSHDKEY
ENV : ?????:34615
USER: SAPFRASHD
"
Can someone help?
Thanks.